QUBINO
Qubino Flush RGBW Dimmer
SKU: ZMNHWD1
Quickstart
This is a
Include the R.G.B.W. color LED Dimmer intor the Z-Wave network, press service button 3 times in 2 seconds.If the device is properly include the green light will remains on.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Qubino Flush RGBW module is used to control RGB/RGBW strips and LED strips or bulbs to create countless colour options and has 5 special scene effects. It can also control halogen lights and fans. Its extremely small size allows for easy installation behind wall sockets and switches. Controlled devices may be powered by 12 or 24 VDC. All IN and OUT terminals may be user configured for LED control or 100 k signal readouts.
| Reset to factory default | Please note that re-including the proudct will reset the data to the default values. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | Include the R.G.B.W. color LED Dimmer intor the Z-Wave network, press service button 3 times in 2 seconds.If the device is properly include the green light will remains on. |
| Exclusion | Exclude the Flush RGBW Dimmer into Z-Wave network, press 3 times in 2 seconds.If the device is proporly excluded, the green light will blink and data will bereset to the factory default values. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Input switch type
*.default value 1*. 1-bi-stable switch type*. 2-mono stable(Push button)switch type Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 2 | switch type |
Parameter 2: Switch mode
*.default value 1*. 1-Normal Mode*. 2-Brightness Mode*. 3-Rainbow Mode Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 3 | Switch mode |
Parameter 3: Auto Scene Mode set
*.default value 1-Ocean2-lightning3-Rainbow Mode4-Snow5-Sun Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 5 | Auto Scene Mode set |
Parameter 4: Auto scene duration
* default value 3* 1-127 delay duration is from 1s to 127s* -128~-1 delay duration is from 1 min. to 127min. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 127 | duration is from 1s to 127s |
| -128 - -1 | duration is from 1 min. to 127min. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 2.07 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-17015398 |
| Z-Wave Product Id | 0x0159.0x0001.0x0054 |
| Neutral Wire Required | ok |
| Firmware Updatable | |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |