Sercomm
PIR Motion Sensor
SKU: SW-PIR03N
Quickstart
This is a
1.Install the battery and the Pairing LED indicator will be lit for one second to indicate a successful booting.2.It will blink one time every second while scanning the network. 3.If the network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you need to use the tamper switch to trigger the adding (Inclusion) process, and then the sensor will repeat steps from 2 to 3.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
SW-PIR03N is a high-performance, easy-to-install motion sensor provides quality detection on human movements. 1. Compact and Flat Panel Design2. 100 Meters RF Transmission Range3. Detection Angle up to 90 degrees FOV with 15 Meters4. Mirror Optics Design5. Immune to Pets Up to 85 lbs ( 38 kg)6. Built-in Ambient Temperature Sensor7. Battery Life 2 Years8. Low Battery Alert9. OTA Upgrade
| Reset to factory default | Please reset the device to factory default only when the primary controller is missing or inoperable.1.Press the tamper switch 4 times within 2 seconds and hold the 4th press until the PIR LED lights up. 2.The PIR LED will be off after 3 seconds and all settings will be reset to factory defaults. |
| Inclusion | 1.Install the battery and the Pairing LED indicator will be lit for one second to indicate a successful booting.2.It will blink one time every second while scanning the network. 3.If the network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you need to use the tamper switch to trigger the adding (Inclusion) process, and then the sensor will repeat steps from 2 to 3. |
| Exclusion | 1.Set the Z-Wave controller to "Exclusion" mode.2.Press the tamper button 3 times within 2 seconds.3.The PIR LED will light up for 1 second if success.4.The device will begin to search for a new network. |
| NIF | XXXNIF |
| Wakeup | Remove the back cover to wake up SW-PIR03N. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline service that assigned to Sensor (Motion detector) statusOpen/Close. It enables the sensor to send reports and readings to a Z-Wave Controller or Z-Wave Gateway whenever the sensor is triggered. |
| 2 | 5 | allows for Sending Basic to associated devices in this group. |
Configuration Parameters
Parameter 1: Configure motion trigger interval
After motion detected, ignores consequent motion events during the trigger interval to save battery power. If Walk Test jumper is enabled, the interval will be set to 2 seconds and ignores this configuration. Size: 2 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 2 - 180 | Unit: 1s |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.07 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-16125369 |
| Z-Wave Product Id | 0x0151.0x0101.0x0001 |
| Sensors | Air Temperature |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |