This is a
1. Follow the instructions for your Z-Wave certified controller toinclude a device to the Z-Wave network.2. Once the controller is ready to include your device, pressand release the top or bottom of the wireless smart dimmer(rocker) to include it in the network.
Transform any home into a smart home with the Jasco Z-Wave In-Wall Smart Toggle Dimmer. The dimmer enables wireless control of on/off and dim functions of hard-wired dimmable LED/CFL and incandescent lighting. The dimmer replaces your current light switch, uses your existing wiring, and provides Z-Wave wireless and in-wall control of overhead lighting. Use the dimmer feature to customize the lighting output and create the perfect ambiance for any room. Providing ultimate flexibility, the In-Wall Smart Dimmer allows you to operate the switch by itself or easily integrate the switch three-way or four-way wiring configurations by adding the Jasco Add-On Switch. Single Pole wiring configuration controls the light from one location. Three-way wiring configuration controls the light from two separate locations. Four-way wiring configuration controls the light from three separate locations. The Jasco Add-On Switch is required for three-way or four-way installations. Take control of your home lighting with Jasco Z-Wave Wireless Lighting Controls!
Reset to factory default | 1. Quickly press ON (up) button (3) times then immediately press the OFF (down) button (3) times. Note: This should only be used in the even your network's primary controller is missing or otherwise inoperable. |
Inclusion | 1. Follow the instructions for your Z-Wave certified controller toinclude a device to the Z-Wave network.2. Once the controller is ready to include your device, pressand release the top or bottom of the wireless smart dimmer(rocker) to include it in the network. |
Exclusion | 1. Follow the instructions for your Z-Wave certified controller toexclude a device from the Z-Wave network.2. Once the controller is ready to Exclude your device, pressand release the top or bottom of the wireless smart dimmer(rocker) to exclude it from the network. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline, Multilevel Switch Report |
2 | 5 | Supports Basic Set and is controlled with the local load |
3 | 5 | Supports Basic Set and is controlled by double pressing the On or Off button |
Dim Rate Adjustments Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Timing of steps |
Dim Rate Adjustments Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Number of steps or levels |
Dim Rate Adjustments Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Timing of steps or levels |
Invert Switch Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Default |
1 | Invert |
Dim Rate Adjustments Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Number of steps or levels |
Dim Rate Adjusments Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Timing of steps or levels |
Dim Rate Adjustments Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Number of steps or levels |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 5.20 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16125348 |
Z-Wave Product Id | 0x0063.0x4944.0x3137 |
Neutral Wire Required | ok |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |