This is a
Network Health Tool:Using the Z-Wave controller you intend to troubleshoot, begin the inclusion process to add a new generic Z-Wave device. Select LEARN on the Network Health Tool Device List widget. The Z-Wave controller may include the ZWP-TBX as a generic scene controller or similar device; name the device according to your troubleshooting needs.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
The Z-Wave Toolbox is a self-contained tool that enables the user to easily troubleshoot Z-Wave networks. Whether the problem is a range issue, interference, or device placement, the Z-Wave Toolbox will make troubleshooting a breezeThe toolbox is a web-based, flexible tool that will work withany operating system, even smart phones and tablets. The toolbox contains 3 major applications, The Z-Wave Packet Analyzer, the Spectrum Analyzer, and the Network Health Tester.The Z-Wave Packet Analyzer allows the user to see Z-Wave traffic. It helps troubleshoot connections, identify abnormal device operation, and pinpoint weak spots. The Spectrum Analyzer allows users to scan frequencies close to Z-Wave frequencies for any interference. Network Health Tester. This powerful tool can determine link stability, quality of service, latencies, and can help the user totroubleshoot, optimize, and deploy Z-Wave networks with confidence. Technical details:Self-contained hardware that does not need computer to operateConnectivity - Ethernet, WiFi (AP and Client mode)Low power; it can run on batteries (battery pack sold separately)Power Adapter (12V/1A, 100-240VAC)FCC and CE compliant
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Hardware Platform | ZM5202 |
Device Type | Sub System Controller |
Network Operation | Sub Static Controller |
Firmware Version | HW: 1 FW: 1.22:01.22 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16125344 |
Z-Wave Product Id | 0x0315.0x0001.0x0001 |
Color | White |
Communications Connections | Ethernet (Wired)Ethernet (Wireless/WiFi) |
Firmware Updatable | Updatable by Consumer via Internet |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |