Jasco Products Company
In-Wall Smart Motion Dimmer
SKU: 26933
Quickstart
This is a
1. Follow the instructions for your Z-Wave certifiedcontroller to add the smart dimmer to the Z-Wavenetwork.2. Once the controller is ready to add your smartdimmer, press and release the top or bottombutton on the smart dimmer to include it in thenetwork.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the GE In-Wall Smart Motion Dimmer. This Z-Wave device replaces you current light switch using your existing wiring and provides Z-Wave wireless control of overhead lighting. The dimmer enables wireless control of On/Off functions of incandescent, LED, xenon, halogen and fluorescent lighting. Not only does it act as a dimmer but the GE In-Wall Smart Motion Dimmer has a built in PIR sensor which can control the local load and be set in occupancy or vacancy mode.
| Reset to factory default | Press and release the top button ten times within 5seconds. The LED will flash 3 times quickly confirmingchange.Note: This should only be used in the event yournetworks primary controller is missing or otherwiseinoperable |
| Inclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to add the smart dimmer to the Z-Wavenetwork.2. Once the controller is ready to add your smartdimmer, press and release the top or bottombutton on the smart dimmer to include it in thenetwork. |
| Exclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to remove a device from the Z-Wavenetwork.2. Once the controller is ready to remove your device,press and release the top button on the smartdimmer to remove it from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline, Multi-Level Report |
| 2 | 5 | Supports Basic Set and is controlled by pressing On/Off button with local load |
| 3 | 5 | Supports Basic Set and is controlled by pressing On/Off button with local load |
Configuration Parameters
Parameter 1: Timeout Duration
0=Test(5S)1=1 minute5=5 minutes15=15 minutes30=30 minutes0xFF=Disable timeout Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 5 | 5 minutes |
| 15 | 15 minutes |
| 0 | Test(5S) |
| 1 | 1 minute |
| 30 | 30 minutes |
| 255 | Disable timeout |
Parameter 10: Adjust timing of steps/levels
Adjust timing of steps/levels Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 4 - 255 | Steps/Levels |
| 1 - 2 | Steps/Levels |
| 3 | Default |
Parameter 11: Adjust Steps/levels with ALL ON/OFF command
Adjust Steps/levels with ALL ON/OFF command Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Default |
| 2 - 99 | Steps/Levels |
Parameter 12: Adjust timing of stepsALL ON/OFF command/levels with
Adjust timing of steps/levels with ALL ON/OFF command Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 2 | Steps/Levels |
| 3 | Default |
| 4 - 255 | Steps/Levels |
Parameter 13: Motion sensing sensitivity
1=High sensitivity2=Medium sensitivity3=Low sensitivity Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 | High Sensitivity |
| 2 | Medium Sensitivity (Default) |
| 3 | Low Sensitivity |
Parameter 14: Enable/Disable Light Sensing
0=Disabled1=Enabled Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled (Default) |
| 1 | Enabled |
Parameter 15: Reset Cycle
0=Disable1=10 seconds2=20 seconds3=30 seconds4=45 seconds110 =27 mins 15 seconds Size: 2 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | 10 seconds |
| 2 | 20 seconds (Default) |
| 3 | 30 seconds |
| 4 | 45 seconds |
| 5 - 109 | 15 second intervals, starting at 60 seconds |
| 110 | 27 minutes 15 seconds |
Parameter 16: Switch Mode
0=Disabled1=Enabled Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled (Default) |
| 1 | Enabled |
Parameter 17: Switch Level
0=Disabled1=Level 199=Level 99(full brightness) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled (Default) |
| 1 - 99 | Brightness Level |
Parameter 18: Dim up rate
0 = Dim up the light to the default level quickly1 = Dim up the light to the default level slowly Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Dim up the light to the default level quickly (Default) |
| 1 | Dim up the light to the default level slowly |
Parameter 19: Exclusion mode
0 = Press any button on the switch1 = press and releaseX button, then press and releaseONbutton Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Press any button on the switch (Default) |
| 1 | Press and releaseX button, then press and releaseONbutton |
Parameter 2: Change brightness of associated light bulb(s)
0xFF = last dimming level Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 - 99 | Brightness levels |
| 255 | Default |
Parameter 3: Operation Mode
1=Manual2=Vacancy3= Occupancy Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 | Manual |
| 2 | Vacancy |
| 3 | Occupancy |
Parameter 5: Invert Switch
In a 3-way configuration, invert the connected Add-On Switch buttons0=Disabled1=Enable Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 6: Enable/Disable Motion Sensor
0=Disabled1=Enable Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enable |
Parameter 7: Adjust steps/levels with Remote
Adjust steps/levels with Remote Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Default |
| 2 - 99 | Steps/Levels |
Parameter 8: Adjust timing of steps/levels with Remote
Adjust timing of steps/levels with Remote Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 2 | Steps/Levels |
| 3 | Default |
| 4 - 255 | Steps/Levels |
Parameter 9: Adjust steps/levels
Adjust steps/levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 2 - 99 | Steps/Levels |
| 1 | Default |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.50 |
| Z-Wave Version | 6.51.08 |
| Certification ID | ZC10-16125342 |
| Z-Wave Product Id | 0x0063.0x494D.0x3034 |
| Firmware Updatable | Updatable by Consumer by RF |
| Sensors | Motion/No Motion (Binary) |
| Neutral Wire Required | ok |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |