This is a
1. Follow the instructions for your Z-Wave certifiedcontroller to add the smart dimmer to the Z-Wavenetwork.2. Once the controller is ready to add your smartdimmer, press and release the top or bottombutton on the smart dimmer to include it in thenetwork.
Transform any home into a smart home with the Jasco In-Wall Smart Motion Dimmer. This Z-Wave device replaces you current light switch using your existing wiring and provides Z-Wave wireless control of overhead lighting. The dimmer enables wireless control of On/Off functions of incandescent, LED, xenon, halogen and fluorescent lighting. Not only does it act as a dimmer but the Jasco In-Wall Smart Motion Dimmer has a built in PIR sensor which can control the local load and be set in occupancy or vacancy mode.
Reset to factory default | Press and release the top button ten times within 5seconds. The LED will flash 3 times quickly confirmingchange.Note: This should only be used in the event yournetworks primary controller is missing or otherwiseinoperable |
Inclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to add the smart dimmer to the Z-Wavenetwork.2. Once the controller is ready to add your smartdimmer, press and release the top or bottombutton on the smart dimmer to include it in thenetwork. |
Exclusion | 1. Follow the instructions for your Z-Wave certifiedcontroller to remove a device from the Z-Wavenetwork.2. Once the controller is ready to remove your device,press and release the top button on the smartdimmer to remove it from the network. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline, Multi-Level Report |
2 | 5 | Supports Basic Set and is controlled by pressing On/Off button with local load |
3 | 5 | Supports Basic Set and is controlled by pressing On/Off button with local load |
0=Test(5S)1=1 minute5=5 minutes15=15 minutes30=30 minutes0xFF=Disable timeout Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | Test(5S) |
1 | 1 minute |
5 | 5 minutes |
15 | 15 minutes |
30 | 30 minutes |
255 | Disable timeout |
Adjust timing of steps/levels Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2 | Steps/Levels |
3 | Default |
4 - 255 | Steps/Levels |
Adjust Steps/levels with ALL ON/OFF command Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Default |
2 - 99 | Steps/Levels |
Adjust timing of steps/levels with ALL ON/OFF command Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2 | Steps/Levels |
3 | Default |
4 - 255 | Steps/Levels |
1=High sensitivity2=Medium sensitivity3=Low sensitivity Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
1 | High Sensitivity |
2 | Medium Sensitivity (Default) |
3 | Low Sensitivity |
0=Disabled1=Enabled Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disabled (Default) |
1 | Enabled |
0=Disable1=10 seconds2=20 seconds3=30 seconds4=45 seconds110 =27 mins 15 seconds Size: 2 Byte, Default Value: 2
Setting | Description |
---|---|
0 | Disable |
1 | 10 seconds |
2 | 20 seconds (Default) |
3 | 30 seconds |
4 | 45 seconds |
5 - 109 | 15 second intervals, starting at 60 seconds |
110 | 27 minutes 15 seconds |
0=Disabled1=Enabled Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disabled (Default) |
1 | Enabled |
0=Disabled1=Level 199=Level 99(full brightness) Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disabled (Default) |
1 - 99 | Brightness Level |
0 = Dim up the light to the default level quickly1 = Dim up the light to the default level slowly Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Dim up the light to the default level quickly (Default) |
1 | Dim up the light to the default level slowly |
0 = Press any button on the switch1 = press and releaseX button, then press and releaseONbutton Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Press any button on the switch (Default) |
1 | Press and releaseX button, then press and releaseONbutton |
0xFF = last dimming level Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 - 99 | Brightness levels |
255 | Default |
1=Manual2=Vacancy3= Occupancy Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 | Manual |
2 | Vacancy |
3 | Occupancy |
In a 3-way configuration, invert the connected Add-On Switch buttons0=Disabled1=Enable Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disabled |
1 | Enabled |
0=Disabled1=Enable Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disabled |
1 | Enable |
Adjust steps/levels with Remote Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Default |
2 - 99 | Steps/Levels |
Adjust timing of steps/levels with Remote Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2 | Steps/Levels |
3 | Default |
4 - 255 | Steps/Levels |
Adjust steps/levels Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Default |
2 - 99 | Steps/Levels |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 5.50 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16125335 |
Z-Wave Product Id | 0x0063.0x494D.0x3033 |
Sensors | Motion/No Motion (Binary) |
Firmware Updatable | Updatable by Consumer by RF |
Neutral Wire Required | ok |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |