Quickstart

This is a On/Off Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
When the pushbutton is released after a press of (2sec

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Simon Electronic Switch IO integrated by Electronic Switch that provides power Switch and Rocker that provides Z-Wave communication attributes.

Reset to factory default	When the pushbutton is released after a press of (20sec
Inclusion	When the pushbutton is released after a press of (2sec
Exclusion	When the pushbutton is released after a press of (2sec
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	3	Z-Wave Plus Lifeline;Commands send to Life LineStatus Change: Command Class Basic - Basic ReportOutput Power change more than 10%:Command Class Meter - Meter Report

Configuration Parameters

Parameter 1: Association LED

Used during Association process by Simon Shortcut Switch IO to turn ON the main LED of all devices already associated to this shortcut.
Size: 1 Byte, Default Value: 0

Setting Description
0 Turns the main LED OFF

255 Turns the main LED ON

Setting	Description
0	Turns the main LED OFF
255	Turns the main LED ON

Parameter 10: Delay ON

delay from activation request until load activation.Please note that possible values are referenced in HEX format from 0x00 to 0xFF (unsigned 1 byte values).Please Refer to u0022Z-Wave Command Class Specification, A-Mu0022 --> u0022Multilevel Switch Set Commandu0022 --> u0022Duration Tableu0022 specification to lean more about these values meaning.
Size: 1 Byte, Default Value: 0

Setting Description
128 - 254 Delay in minutes From 1 to 127

0 - 127 Delay in seconds

Setting	Description
128 - 254	Delay in minutes From 1 to 127
0 - 127	Delay in seconds

Parameter 11: Activation Time

Time that load performs activated after complete an activation process.Please note that possible values are referenced in HEX format from 0x00 to 0xFF (unsigned 1 byte values).Please Refer to u0022Z-Wave Command Class Specification, A-Mu0022 --> u0022Multilevel Switch Set Commandu0022 --> u0022Duration Tableu0022 specification to lean more about these values meaning.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 127 Delay in seconds

128 - 254 Delay in minutes From 1 to 127

Setting	Description
0 - 127	Delay in seconds
128 - 254	Delay in minutes From 1 to 127

Parameter 12: Behavior of LED in Repose

Configuration of Main LED as identification at 20%.
Size: 1 Byte, Default Value: 0

Setting Description
0 LED OFF

255 LED ON at 20% of maximum level

Setting	Description
0	LED OFF
255	LED ON at 20% of maximum level

Parameter 13: Lock Input

Locks the pushbutton and wired input actions.
Size: 1 Byte, Default Value: 0

Setting Description
0 Unlock the direct control of load

255 Lock the direct control of load

Setting	Description
0	Unlock the direct control of load
255	Lock the direct control of load

Parameter 15: Reset Default

Parameters, Groups, and Z-Wave status are restored to default. (Only writable)
Size: 2 Byte, Default Value: 0

Setting Description
39015 Device persorms a factoy default Reset

Setting	Description
39015	Device persorms a factoy default Reset

Parameter 16: Delay OFF

delay from deactivation request until load deactivation.Please note that possible values are referenced in HEX format from 0x00 to 0xFF (unsigned 1 byte values)Please Refer to u0022Z-Wave Command Class Specification, A-Mu0022 --> u0022Multilevel Switch Set Commandu0022 --> u0022Duration Tableu0022 specification to lean more about these values meaning.
Size: 1 Byte, Default Value: 0