This is a
1. Plug the 2-pin AC power plugs of lighting device to the receptacle of 86-1012. Insert the module's 3-pin plug into an AC outlet of your preferred location. In normal operating mode, the LED on the front panel will be lit. 3. Add(Include) the module into your network by a Z-Wave certified controller.Normally, the sequence is as follows:a. Place your network controller into inclusion mode by following the controller manufacturer's instructionsb. When the controller is ready, single click the button on the front of 86-101c. The controller should indicate that the new device was added successfully.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
86-101 Plug in Dimmer Module Works with any AC operated lamps with incandescent and dimmable florescent(CFL) or LED light bulbs ON/OFF status and location LED indicator Can be controlled wirelessly or manually Plug and play, simple setup Lightweight and compact.Grounded 3-pin AC power plug to enhance safetyOver-The-Air firmware upgrade available with compatible gateway, Z-Wave static controller, PC and software Z-Wave 500 Series module inside Internal resettable fuse to protect from surge current Manual reset capability Adjustable dimming rate
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Use this procedure only in the event that the network primary controller is lost or otherwise inoperable.1. Unplug the 86-101 from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)2. Press and hold the button on the 86-1013. Plug the 86-101 back into the AC outlet with the button pressed4. After 3 seconds, release the button. If you see the button blink, that means that the 86-101 has been reset successfully
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Indicates the time duration of each level. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Indicates the time duration of each level. |
LED indicator will be ON/OFF when connected to appliance depending on the configuration value. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | LED indicator will be OFF when the connected appliance is ON, and the LED indicator will be ON when the connected appliance is OFF |
1 | the LED indicator will be ON when the connected appliance is ON, and the LED indicator will be OFF when the connected appliance is OFF |
2 | the LED indicator is always OFF regardless of the load condition |
The time interval of brightness change between dimmingup and down can be adjusted Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Indicates the number of levels the lighting will change when the timer runs out. |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 5.07 |
Z-Wave Version | 6.51.02 |
Certification ID | ZC10-16105285 |
Z-Wave Product Id | 0x0307.0x5044.0x4744 |
Firmware Updatable | Updatable by Professional/Technician |
Outdoor Use | ok |
Color | White |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |