This is a
Click [Add] icon in Z-Wave PC Controller Program. Press the [REG] button for 3 seconds. (Ding dong -> Ding ding) Press the [*] button after pressing the [00[*] button.( Success : Ding dong dang, Fail : Ding dong Ding dong )
Touch Screen Type HandleDoor Lock. The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products.
Reset to factory default | All registered Master/User data will be deleted, and Master PIN Code is set to 1234. Also Z-Wave Door Lock will be removed from the network. Press the [REG] button for 3 seconds. (Ding dong -> Ding ding) Press the [*] button after pressing the [4560852580] button.(Success: Ding ding dang, Fail : Ding dong Ding dong) Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
Inclusion | Click [Add] icon in Z-Wave PC Controller Program. Press the [REG] button for 3 seconds. (Ding dong -> Ding ding) Press the [*] button after pressing the [00[*] button.( Success : Ding dong dang, Fail : Ding dong Ding dong ) |
Exclusion | After exclusion from Z-Wave Network, it will no longer be remotely-controlled via the controller.Click [Remove] icon in Z-Wave PC Controller Program.Press the [REG] button for 3 seconds. (Ding dong -> Ding ding)Press the [*] button after pressing the [00] button. (Success : Ding dong dang, Fail : Ding dong Ding dong) |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline |
This value can be used when the device is connected with platform of Samsung SDS.This function is not related to Z-Wave CC.- 0x02 : Command for disable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function , '0x00' will be reported.- 0x03 : Command for enable which is set by platform of Samsung SDS. After setting, if you try to get value of Security Function, '0x01' will be reported.- 0x04 : 'Request for Enable' command which is reported by Doorlock. This cannot be set.(8th function in manual)- 0x05 : If the request for 'Request for Enable' command is failed in platform, this will be set by platform of Samsung SDS.Value of Security Function is not changed by this command. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable (Default) |
1 | Enable |
2 | System Disable |
3 | System Enable |
4 | Request for Enable |
5 | Fail |
Privacy Mode Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable (Default) |
0 - 1 | Enable |
This parameter is supported to Configuration Get Command only. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 30 | The number of registered user codes. |
Hardware Platform | ZM5101 |
Device Type | Door Lock - Keypad |
Network Operation | Listening Sleeping Slave |
Firmware Version | HW: 1 FW: 1.03 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-16105270 |
Z-Wave Product Id | 0x022E.0x0001.0x0001 |
Door Lock Type | Lever Handle |
Color | Black |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |