This is a
Leviton Decora Smart Z-Wave devices support two methods of inclusion.When using a Z-Wave Plus certified controller choose Network Wide Inclusion.Network Wide Inclusion:Network Wide Inclusion allows your device to be added to the network using devices already in the network to assist with communication. Work your way from the closest devices to the controller outward. Enter Programming Mode by holding the control button for 7 seconds, the Locator LED will blink amber. Tap the control button one time.The Locator LED will quickly flash green. The Decora Smart Z-Wave device is ready to learn into the Z-Wave network. Follow directions in the Z-Wave controller to complete the adding process. Upon successful addition to network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times.Traditional Inclusion:For older controllers Traditional Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including. Enter Programming Mode by holding the control button for 7 seconds, the Locator LED will blink amber. The Decora Smart Z-Wave device is ready to add to the Z-Wave network. Follow directions in the Z-Wave controller to enter learn mode. Tap the control button one time. The Locator LED will quickly flash green.The Z-Wave controller will begin to pair with the Decora Smart device. Upon successful addition to the network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times.
The wireless Leviton DZPD3 is a Z-Wave enabled plug-in dimmer designed for use for most residential lighting applications to control LED, CFL, and incandescent bulbs. The DZPD3 Dimmer is fully compatible with Z-Wave Plus certified controllers. Provides full range dimming with adjustable fade rates.Manufacturer Parameters allow custom configuration via Z-Wave commands.Rated for 100W LED and CFL dimmable bulbs and 300W incandescent bulbs.These Z-Wave Plus devices support beaming, network wide inclusion, and over the air updates.
Reset to factory default | When removing a device from a network it is best practice to use the Exclusion process. Insituations where a device needs to be returned to factory default follow the following steps.A reset should only be used when a controller is inoperable or missing: Holding the control button for a total of 14 seconds.- After the first 7 seconds the LED turns amber.- The Locator LED will quickly flash red/amber after 14 seconds. Release the control button and the device will reset. |
Inclusion | Leviton Decora Smart Z-Wave devices support two methods of inclusion.When using a Z-Wave Plus certified controller choose Network Wide Inclusion.Network Wide Inclusion:Network Wide Inclusion allows your device to be added to the network using devices already in the network to assist with communication. Work your way from the closest devices to the controller outward. Enter Programming Mode by holding the control button for 7 seconds, the Locator LED will blink amber. Tap the control button one time.The Locator LED will quickly flash green. The Decora Smart Z-Wave device is ready to learn into the Z-Wave network. Follow directions in the Z-Wave controller to complete the adding process. Upon successful addition to network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times.Traditional Inclusion:For older controllers Traditional Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including. Enter Programming Mode by holding the control button for 7 seconds, the Locator LED will blink amber. The Decora Smart Z-Wave device is ready to add to the Z-Wave network. Follow directions in the Z-Wave controller to enter learn mode. Tap the control button one time. The Locator LED will quickly flash green.The Z-Wave controller will begin to pair with the Decora Smart device. Upon successful addition to the network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times. |
Exclusion | When removing a device from a Z-Wave network best practice is to use the exclusion command found in the Z-Wave controller. Enter Programming Mode by holding the control button for 7 seconds, the Locator LED will turn amber. Follow directions in the Z-Wave controller to enter exclusion mode. Tap the control button one time. The Locator LED will quickly flash green.The Z-Wave controller will exclude the Decora Smart device. The Z-Wave controller will confirm successful exclusion from the network. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave PlusTM Lifeline: A NOTIFICATION frame is sent to the nodesin this association group when a Lifeline event occurs. All nodes in the association group |
Fade On Time Parameter No: 1, Length: 1 Byte Valid Values = 0 to 253 (default 2)- 0 = Instant On- 1 - 127 = Seconds: 1 - 127 seconds- 128 - 253 (0x80 - 0xFD) = Minutes: 1 - 126 minutes Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
128 - 253 | 1-126 Minutes |
0 - 253 | Valid Values |
0 | Instant On |
1 - 127 | 1-127 Seconds |
Fade Off Time Parameter No: 2, Length: 1 Byte Valid Values = 0 to 253 (default 2)- 0 = Instant Off- 1 - 127 = Seconds: 1 - 127 seconds- 128 - 253 (0x80 - 0xFD) = Minutes: 1 - 126 minutes Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
128 - 253 | 1-126 Minutes |
0 - 253 | Valid Values |
0 | Instant Off |
1 - 127 | 1-127 Seconds |
Minimum Light Level Parameter No: 3, Length: 1 Byte Valid Values = 0 to 100 (default 10) Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 - 100 | Valid Values |
Maximum Light Level Parameter No: 4, Length: 1 Byte Valid Values = 0 to 100 (default 100) Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 - 100 | Valid Values |
Locator LED Status Parameter No: 7, Length: 1 Byte Valid Values = 0 to 255 (default 255)- 0 = LED Off- 254 (0xFE) = Status Mode- 255 (0xFF) = Locator Mode Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | LED Off |
254 | LED Status Mode |
255 | LED Locator Mode |
Load Type Parameter No: 8, Length: 1 Byte Valid Values = 0 to 2 (default 0)- 0 = Incandescent- 1 = LED- 2 = CFL Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 2 | Load Type |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 1.22 |
Z-Wave Version | 6.61.00 |
Certification ID | ZC10-16095237 |
Z-Wave Product Id | 0x001D.0x3501.0x0001 |
Firmware Updatable | Updatable by Consumer by RF |
Z-Wave Scene Type | Scene |
Color | White |
Electric Load Type | Dimmable LEDIncandescentLED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |