This is a
To include RGB BULB into a Z-Wave network as a non-security device:(1) Make sure the power supply is disconnected and the RGB BULB islocated within a direct Z-Wave network's main controllercommunication range.(2) Set the Z-Wave network main controller into learning mode(see Z-Wave network controller operating manual).(3) Insert the RGB BULB into a lamp-socket and then power on.(4) Auto-inclusion will be activated. If the inclusion is successful, theRGB BULB will blink fast in blue for less than 5 seconds and thenkeep on for 3 seconds. RGB BULB will keep on in the color before itis included into the Z-Wave network after the inclusion procedureis finished.To include RGB BULB into a Z-Wave network as a security device:(1) Screw in the RGB BULB.(2) Set the Z-Wave network main controller into learning mode(see Z-Wave network controller operating manual).(3) Toggle the wall switch off and on 3 times quickly (within 3 secondsand the final ending position of the wall switch must be on).(4) If the inclusion is successful, the RGB BULB will blink fast in greenfor less than 5 seconds and then keep on 3 seconds. RGB BULB willkeep on in the color before it is included into the Z-Wave networkafter the inclusion procedure is finished.
RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.
Reset to factory default | There are two ways to reset the RGB BULB. One is that removingRGB BULB from the Z-Wave network, the other is that using theconfiguration command class. |
Inclusion | To include RGB BULB into a Z-Wave network as a non-security device:(1) Make sure the power supply is disconnected and the RGB BULB islocated within a direct Z-Wave network's main controllercommunication range.(2) Set the Z-Wave network main controller into learning mode(see Z-Wave network controller operating manual).(3) Insert the RGB BULB into a lamp-socket and then power on.(4) Auto-inclusion will be activated. If the inclusion is successful, theRGB BULB will blink fast in blue for less than 5 seconds and thenkeep on for 3 seconds. RGB BULB will keep on in the color before itis included into the Z-Wave network after the inclusion procedureis finished.To include RGB BULB into a Z-Wave network as a security device:(1) Screw in the RGB BULB.(2) Set the Z-Wave network main controller into learning mode(see Z-Wave network controller operating manual).(3) Toggle the wall switch off and on 3 times quickly (within 3 secondsand the final ending position of the wall switch must be on).(4) If the inclusion is successful, the RGB BULB will blink fast in greenfor less than 5 seconds and then keep on 3 seconds. RGB BULB willkeep on in the color before it is included into the Z-Wave networkafter the inclusion procedure is finished. |
Exclusion | To remove the RGB BULB from the Z-Wave network:(1) Screw in the RGB BULB.(2) Set the Z-Wave network main controller into excluding mode(see Z-Wave controller operating manual).(3) Toggle the wall switch off and on 3 times quickly(within 3and the final ending position of the wall switch must be on),if the exclusion is successful, the RGB BULB will blink fast inorange for less than 5 seconds and then keep on for 3 seconds.RGB BULB will keep on warm white after the exclusion procedureis finished. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus LifelineRGB BULB supports only one association groupings:RGB BULB will send the follow notification to the associated nodes whenthe status of the RGB BULB is changed.1. Set Configuration parameter 24 to 0: Reserved2. Set Configuration parameter 24 to 1: Send Basic Report3. Set Configuration parameter 24 to 2: Send Basic Report only when thestatus of the RGB BULB is not changed by Z-WAVE Command. |
Define how the RGB BULB will react after the power supply is back on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Define how the RGB BULB will react after the power supply is back on. |
1 | RGB BULB memorizes its state after a power failure. |
2 | RGB bulb does not memorize its state after a power failure. |
RGB BULB can send notifications to associated device (Group Lifeline)when the status of the RGB BULB is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | Send Basic report |
2 | Send BASIC REPORT only when the status of the RGB BULB is not changed by Z-WAVE command. |
RGB BULB will exclude from the Z-Wave network with thisparticular command. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1431655765 | Resetting to the factory default. |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.01 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16095231 |
Z-Wave Product Id | 0x0208.0x0100.0x0004 |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |