Hank
Smart Switch
SKU: HKZW-SW01
Quickstart
This is a
1) Connect the power supply.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple click the Z-Button, LED indicator should blink fast4) Smart Switch should be recognized and included into the Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Smart Switch is a Z-Wave Switch module specifically used to enable Z-Wave command and control (on/off) of any connected device such as bulbs.
| Reset to factory default | 1) Power on the Switch.2) Press and hold the Z-button for more than 20 seconds.3) If holding time more than one second, the LED will blink faster and faster. If holding time more than 20 seconds, the LED indicator will be on for 3 seconds, which indicates that the reset is complete, then it will blink slowly indicating that it is not a part of a Z-Wave network.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | 1) Connect the power supply.2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).3) Triple click the Z-Button, LED indicator should blink fast4) Smart Switch should be recognized and included into the Z-Wave network. |
| Exclusion | 1) Connect the power supply.2) Set the Z-Wave network controller into the remove mode (see Z-Wave controller operating manual)3) Triple click the Z-button. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus LifelineSmart Switch will send basic report to the associated nodes whenever it is turned on or off |
Configuration Parameters
Parameter 21: Setting device status after power failure
Define how the Smart Switch reacts after the power supply is back on. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Smart Switch memorizes its state after a power failure |
| 1 | Smart Switch will be on after the power supply is reconnected. |
| 2 | Smart Switch will be off after the power supply is reconnected. |
Parameter 24: Notification when Load status change
Smart Switch can send notifications to association device (Group Lifeline) when state of Smart Switchs load is changed. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 1 | Send Basic report. |
| 2 | Send Basic report only when Load condition is not changed by Z-WAVE Command. |
Parameter 27: Indicator modes
After Smart Switch being included into a Z-Wave network, the LED in the device will indicator the state of load. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The LED will follow the status (on/off) of its load. |
| 1 | When the state of Smart Switchs load changed, The LED will follow the status (on/off) of its load, but the red LED will turn off after 5 seconds if there is no more switch action. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.03 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-16085169 |
| Z-Wave Product Id | 0x0208.0x0101.0x0003 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Electric Load Type | FluorescentIncandescentInductive (e.g. Motor)LED |
| Neutral Wire Required | ok |
| Switch Type | Decorator Paddle Rocker |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |