Quickstart
This is a
Siren for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
The Z-Wave Plus Siren must be added to a Z-Wave network prior to use. To include the siren in a network both the siren and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. 1)Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Siren.2)Locate the power outlet desired to be used with the Z-Wave Plus Siren.3)Put your Z-Wave Plus Controller into add (inclusion) mode. 4)Plug in the Z-Wave Siren and verify a single beep sound is heard.5)The LED on the front of the unit will turn off if successful included into a network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The Ecolink Z-Wave Plus Siren provides home users with a simple way to keep a location safe and secure.The Ecolink Z-Wave Plus Siren can also be used to audibly notify the user of any Z-Wave state changes.The device is as simple to use as plugging in a wall outlet.The device can create 4 independent tones for different alerts to the user.These could include but are not limited to: Security Alarm, entry/exit, smoke/Fire, temperature and more.The Z-Wave Plus Siren can also be used as a Z-Wave Plus network extension.
Reset to factory default |
The Z-Wave Plus Siren is automatically factory defaulted when removed from a Z-Wave network. Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion |
The Z-Wave Plus Siren must be added to a Z-Wave network prior to use. To include the siren in a network both the siren and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. 1)Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Siren.2)Locate the power outlet desired to be used with the Z-Wave Plus Siren.3)Put your Z-Wave Plus Controller into add (inclusion) mode. 4)Plug in the Z-Wave Siren and verify a single beep sound is heard.5)The LED on the front of the unit will turn off if successful included into a network. |
Exclusion |
1)Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.2)Unplug and re-plug in your Z-Wave Plus Siren.3)The device will play a long beep and the LED will begin to breathe if the device is successfully removed from the network. |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
5 |
Z-Wave Plus Lifeline |
Technical Data
Hardware Platform |
ZM5202 |
Device Type |
Siren |
Network Operation |
Always On Slave |
Firmware Version |
HW: 255 FW: 1.10 |
Z-Wave Version |
6.51.06 |
Certification ID |
ZC10-16085156 |
Z-Wave Product Id |
0x014A.0x0005.0x000A |
Communications Protocol |
Z-Wave Serial API |
Color |
White |
Switch Type |
Rotary Knob |
Z-Wave Scene Type |
Scene |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |