Quickstart

This is a Thermostat - HVAC for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
When the device is not added to a Z-Wave network, then triple short clicks of the inclusion button will start the inclusion.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Z-Wave to Systemair HVAC Adapter is an Z-Wave Interface adapter, which connects the Z-Wave network with the Systemair Heat Recovery Ventilation. The Systemair HVAC is a residential HRV system, which can be controlled locally by one or more UI, as well as remotely by a mobile App or a browser via Z-Wave network.

Reset to factory default	To do a Factory Reset the user must follow the following procedure: - Press and hold the inclusion button for 6 seconds, then - Release it, and then - Press it again and hold it for 3 secondsThe Z-Wave Adapter is indicating each phase with a different LED patternsee Operational modes and indicators in the User's Manual.
Inclusion	When the device is not added to a Z-Wave network, then triple short clicks of the inclusion button will start the inclusion.
Exclusion	When the device is already included in a Z-Wave network, then triple short clicks of the inclusion button will exclude it from that Z-Wave network.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: System Type

Read Only Parameter, shows what is the Type of the Systemair HVAC Unit.
Size: 2 Byte, Default Value: 0

Setting Description
0 - 5 See User Manual

12 - 21 See User Manual

Setting	Description
0 - 5	See User Manual
12 - 21	See User Manual

Parameter 2: Filter - Period

Read Only Parameter, shows how long the filter can be used in steps of 30 days. Example 6 = 180 days.
Size: 2 Byte, Default Value: 12

Setting Description
6 x 30 = 180 days

9 x 30 = 270 days

12 x 30 = 360 days

15 x 30 = 450 days

Setting	Description
6	x 30 = 180 days
9	x 30 = 270 days
12	x 30 = 360 days
15	x 30 = 450 days

Parameter 3: Filter - Days Used

Read Only Parameter, shows how many days the filter has been used since the last change. The value can be used to calculate the Filter remaining time by the equation: Filter Remaining Days = (Parameter_2 x 30) - Parameter_3
Size: 2 Byte, Default Value: 0

Setting Description
0 - 500 The counter stops on 500

Setting	Description
0 - 500	The counter stops on 500

Parameter 4: Boost Mode Remaining Time

Read Only Parameter, shows how many seconds are left for Boost mode.
Size: 2 Byte, Default Value: 0

Setting Description
240 - 0 Counts down while Boost mode is active

Setting	Description
240 - 0	Counts down while Boost mode is active

Parameter 5: Temperature Setpoint Step

Read Only Parameter, shows the min change available in degrees Celsius x 10. Example 25 = 2.5 degree Celsius.
Size: 2 Byte, Default Value: 10

Setting Description
10 /10 = 1.0 degrees Celsius step

25 /10 = 2.5 degrees Celsius setp

Setting	Description
10	/10 = 1.0 degrees Celsius step
25	/10 = 2.5 degrees Celsius setp

Parameter 6: CDx New Firmware Version Available

Shows the Firmware Version available in the Z-Wave adapter for the Firmware Target 2. This parameter must be written after successful uploading of the firmware image for the local UI. Example UI Version 5.02.03:MSB - x, don't care,Next - 05,Next - 02,LSB - 03.
Size: 4 Byte, Default Value: 0

Setting Description
0 - 16777215 max version 255.255.255

Setting	Description
0 - 16777215	max version 255.255.255

Parameter 7: PCU-ECx New Firmware Version Available

Shows the Firmware Version available in the Z-Wave adapter for the Firmware Target 1. This parameter must be written after successful uploading of the firmware image for the Ventilation Unit. Example Ventilation Unit Version 6.07.08:MSB - x, don't care,Next - 06,Next - 07,LSB - 08.
Size: 4 Byte, Default Value: 0