This is a
1. Put Primary Controller into Inclusion Mode2. Press and Hold Control Programming Button for >2seconds, release when Green LED flashes
Enjoy the comfort, convenience and energy efficiency of beautiful custom motorized window treatments featuring Z-Wave protocol for easy integration.Lighting control has never been more simple. Window treatments can be automated using your favorite Z-Wave certified gateway or security system, or controlled by a remote control.Raise or lower the shades to control just the right amount of light, privacy and solar heat. Shades can be fully open, fully closed or anywhere in between, its up to you.In addition, some systems will also report back the state of the battery charge on battery operated versions.
Reset to factory default | Press and hold the button on the control for approximately 15 seconds (the LED will stop flashing when complete."Please use this procedure only when the network primary controller is missing or otherwise inoperable." |
Inclusion | 1. Put Primary Controller into Inclusion Mode2. Press and Hold Control Programming Button for >2seconds, release when Green LED flashes |
Exclusion | 1. Put Primary Controller into Inclusion Mode2. Press and Hold Control Programming Button for >2seconds, release when Green LED flashes |
NIF | XXXNIF |
Wakeup | The Wakeup command class should be configured by a hub when the remote is joined to a Z-Wave network. A WAKE_UP_INTERVAL_SET command should configure the NodeID at a minimum. The Wakeup interval can be configured to any value from 6 minutes to 25 hours. Recommendation is to leave the interval at the default of 12 hours to maximize battery life. The remote will wake up every WakeUpInterval and send a WakeUp Notification command as well as a battery report to the NodeID assigned with the Interval Set command. The WakeUp Notification will be sent within a few minutes of power being applied to the remote and then once every Wake Up Interval. A Wakeup Interval Capabilities command will inform the hub of the default, minimum, maximum and step size of the Wake Up interval. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Association Group #1 is dedicated Lifeline to primary control, primarily used for battery status reports, central scene cc, local reset cc. |
2 | 12 | Association Group #2 is dedicatedfor slave shades. Primary control commands, SWITCH_MULTILEVEL_CC, BASIC_CC BINARY CC |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
1. Press and release Twice on Control Programming button. (Tap 2x on prog button)2.Slave sends NIF
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
1. Press and release Three times on Control Programming button. (Tap 3x on prog button)2. Slave sends NIF
Hardware Platform | ZM5101 |
Device Type | Remote Control - Simple |
Network Operation | Portable Controller |
Firmware Version | HW: 255 FW: 187.65 |
Z-Wave Version | 6.61.00 |
Certification ID | ZC10-16055082 |
Z-Wave Product Id | 0x026E.0x5643.0x5A31 |
Z-Wave Scene Type | Central Scene |
Color | White |
Firmware Updatable | Not Updatable |
Switch Type | Push Button with Indicator |
Window Covering Control Features | Endpoint Aware |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |