Contec - intelligent housing
Da Vinci Wall Controller
SKU: Da Vinci v3
Quickstart
This is a
To Add (Include) to the network:Press the #1 button 3 times.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Da Vinci wall controller is a Multi Chanel Z-Wave device that contains up to 6 relays and up to 9 touch buttons that can be set to control either the relays or any other on/off (SWITCH_BINARY) Z-Wave device.
| Reset to factory default | Double Press the following buttons in thefollowing order 8,1,3.Use the reset procedure only when the primary controller is missing or inoperable. |
| Inclusion | To Add (Include) to the network:Press the #1 button 3 times. |
| Exclusion | To Remove (Exclude) from the network:Press the #1 button 3 times. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 3 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 4 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 5 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 6 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 7 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 8 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 9 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 10 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 11 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 12 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 13 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 14 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 15 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 16 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 17 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
| 18 | 5 | Sends a SWITCH_BINARY_SET command to all group members |
| 19 | 5 | Sends a SWITCH_BINARY_REPORT command to all group members |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Wall Controller |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16055069 |
| Z-Wave Product Id | 0x025D.0x0100.0x0100 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |