This is a
1) Include other devices into Wall Remote's network: * Wall Remote must be primary controller* Press I/E button until green LED flashes* Wall Remote will go back to sleep if no node info received within 10 seconds.2) Exclude other devices from Wall Remote's network: * Wall Remote must be the primary controller* Press I/E button until red LED flashes.* Wall Remote will go back to sleep if no node info received within 10 seconds.
Portable Controller with Wall Remote Control:* Basic Set Mode: 4 buttons control 4 different groups.* Central Scene Mode: 4 buttons control 4 different scenes.* Support Shift Function to Primary Controller)* Battery: CR2032 x 2
Reset to factory default | Press 4 buttons together for 10 seconds. The LED colors will turn red then turn green. (Green LED flashes 5 times quickly that means reset completely).Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable. |
Inclusion | 1) Include other devices into Wall Remote's network: * Wall Remote must be primary controller* Press I/E button until green LED flashes* Wall Remote will go back to sleep if no node info received within 10 seconds.2) Exclude other devices from Wall Remote's network: * Wall Remote must be the primary controller* Press I/E button until red LED flashes.* Wall Remote will go back to sleep if no node info received within 10 seconds. |
Exclusion | 1) Include other devices into Wall Remote's network: * Wall Remote must be primary controller* Press I/E button until green LED flashes* Wall Remote will go back to sleep if no node info received within 10 seconds.2) Exclude other devices from Wall Remote's network: * Wall Remote must be the primary controller* Press I/E button until red LED flashes.* Wall Remote will go back to sleep if no node info received within 10 seconds. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
To Include into (adding into) an existing network: Put the Z-Wave Gateway or Controller into learn mode to add the Wall Remote into your controller. Press button 1 and 4 together till the red LED flashes to be included.ZT1141 will go to sleep if adding is not successfully within 5 seconds.
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
To Exclude from (removing from) an existing network: Put the Z-Wave Gateway or Controller into learn mode to remove the Wall Remote from your controller. Press button 1 and 4 together till the red LED flashes to be excluded.ZT1141 will go to sleep if removing is not successfully within 5 seconds.
Hardware Platform | ZM5101 |
Device Type | Remote Control - Simple |
Network Operation | Portable Controller |
Firmware Version | HW: 2 FW: 10.03 |
Z-Wave Version | 3.2X |
Certification ID | ZC10-16045053 |
Z-Wave Product Id | 0x0109.0x1004.0x0402 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |