Building 36
Building 36 Temperature Sensor
SKU: B36-S10
Quickstart
This is a
Put the Z-Wave controller into add mode (refer to controller documentation for more information).Press the button on the sensor to add to the Z-Wave network. The LED on the sensor will go solid white when the sensor has been successfully added.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Battery powered indoor Z-Wave temperature sensor.Sense temperature in any room in the home.
| Reset to factory default | NOTE: Only reset the sensor to factory default when the primary controller is missing or inoperable.Press and hold the button for 15 seconds.Release the button after 15 seconds and the LED will blink rapidly when the sensor has been reset to factory default. |
| Inclusion | Put the Z-Wave controller into add mode (refer to controller documentation for more information).Press the button on the sensor to add to the Z-Wave network. The LED on the sensor will go solid white when the sensor has been successfully added. |
| Exclusion | Put the Z-Wave controller into remove mode (refer to the controller documentation for more information).Press the button on the sensor to remove from the Z-Wave network.The LED on the sensor will blink white when the sensor has been successfully removed. |
| NIF | XXXNIF |
| Wakeup | The temperature sensor will send wake up notifications when the button is pressed and the temperature sensor is already included in a Z-Wave network.It also sends wake up notifications based at time intervals specified in the wake up set command. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline. |
| 2 | 5 | Sensor Multilevel Temperature Report. |
Configuration Parameters
Parameter 1: Wake Up Period
Number of seconds the sensor will stay in the Wake up state following a button press. The sensor will go to sleep if it receives a wake up no more information frame. Size: 2 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 10 - 32768 | Seconds to stay awake following button press |
Parameter 2: Low Battery Level
Low Battery Report threshold. Size: 2 Byte, Default Value: 1755
| Setting | Description |
|---|---|
| 1000 - 2500 | Battery level |
Parameter 3: Temperature Reporting Threshold
The minimum temperature difference required to send a new ambient temperature report. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 100 | Tenths of a degree Fahrenheit.A value of 10 would be 1.0F. |
Parameter 4: Configuration Bitmask
Configuration bitmask for various device configuration settings. Bit 0 - reserved.Bit 1 - If set to 1, sensor will send unsolicited temperature reports.Bits 2 to 15 - reserved Size: 2 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | If zero, sensor will not send unsolicted temperature reports |
| 2 | If Bit 1 is set, sensor will send unsolicited temperature reports when the temperature changes. |
Parameter 5: Battery Reporting Interval
The number wakeup intervals between autonomous battery reports. Size: 2 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 0 - 255 | Number of wake up intervals between autonomous battery reports.The wake up interval is set in the Wake Up Command Class. |
Parameter 6: Temperature Checking Interval
The number of seconds between temperature readings. Size: 2 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 10 - 255 | The number of seconds between temperature readings |
Parameter 7: Temperature Reporting Interval
The number wakeup intervals between autonomous temperature reports. These interval reports should be sent regardless of the setting of the temperature reporting threshold. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | The number of wake up intervals between autonomous temperature reports.If this value is zero, autonomous temperature reporting based on wake up interval is disabled. |
Parameter 8: Temperature Calibration Offset
Adjust reported temperature by +/- 10 degrees Fahrenheit for calibration. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -100 - 100 | Tenths of a degree Fahrenheit.A value of 10 would be 1.0F. |
Parameter 9: Mandatory Temperature Reporting Interval
Temperature will be reported regardless of differential from threshold. Size: 2 Byte, Default Value: 7200
| Setting | Description |
|---|---|
| 60 - 64800 | The number of seconds between temperature reports. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Multilevel Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | 01 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16010010 |
| Z-Wave Product Id | 0x0190.0x0003.0x0001 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |