This is a
Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of the Bulb to turn it off and then press the external switch again to turn it on.
Oomi Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave. Its a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour.The Bulb is also a security Z-wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.
Reset to factory default | Turn the controller of Z-Wave network into exclusion mode, press the external switch of the Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.After the Bulb is excluded from network, it will be reset to factory default state.Use this procedure only in the event that your primary network controller is missing or inoperable. |
Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of the Bulb to turn it off and then press the external switch again to turn it on. |
Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, press the external switch of the Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | The association group 1 is the Z-Wave Lifeline group.The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1. |
2 | 5 | In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2when the Bulb receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller. |
Enable/disable to lock the configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable. |
1 | Enable. |
Reset your Bulb. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Reset all configuration parameters to default settings. |
1431655765 | Reset the Bulb to factory default settings. |
Enable/disable to send out a report when the Bulbs color is changed. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable. |
1 | Enable and the Hail CC is selected. |
Enable/disable the function of using external switch to turn on/off the bulb. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable. |
Enable/disable the function of using external switch to change the bulbs color. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable. |
To configure which notification report would be sent in association group 1 when the state of Bulb is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Send Nothing. |
1 | Send Hail CC. |
2 | Send Basic Report CC. |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 62 FW: 1.03 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-15120006 |
Z-Wave Product Id | 0x0086.0x0103.0x0062 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |