This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing.
Aeon Labs Doorbell supports playing MP3 music files with a press of this doorbell. It has a 128MB flash memory that can store up to 800 ringtones. The volume can be adjusted manually via short press on the Volume Button, also you can switch the doorbell sound to the next via long press on the Volume Button. You may change/update your doorbell ringtone at any point in time you want by connecting your Doorbell to your PC to update the sound track on your Doorbells flash memory.There is a small Wireless Button, which can trigger the doorbell on the other side of the wall to play the selected doorbell music when pressed.It also act as a repeater that forward Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node.By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary listening Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices.Also a tool that can be programmed, scheduled, controlled and communicated with from anywhere in the world.
Reset to factory default | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable. |
Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing. |
Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the products Action button that you can find on the product's housing. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Association group 1 is the lifeline group. The Doorbell can add max 5 nodes to this group. The Basic report CC or Hail CC (can be configured by parameter 80) can be sent to the associated nodes in association group 1. |
2 | 5 | The Basic Set or Switch Binary Set can be sent to the associated nodes in this group when the Doorbell receives the Basic Set or Switch Binary Set CC from the primary controller. It can add max 5 nodes to this group. |
Define the functions of Button - and Button+ for your Doorbell. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Button - is Previous, Button+ is Next. |
1 | Swap functions of the two buttons. |
Define functions of Button -and Button+when short pressing and long pressing it. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | short pressing changes volume, long pressing changes default ringtone |
1 | long pressing changes volume, short pressing changes default ringtone |
Set the repetitions of playing doorbell ringtone.Note: If the time of playing doorbell ringtone is more than 20s, the volume of ringtone will be reduced to silence no matter how many repetitions of doorbell ringtone are set. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
1 - 100 | The range of repetition is 1 to 100. |
Pair the Wireless Button with your Doorbell.When the Doorbell enters into pair mode, the blue LED will blink slowly, at this time, press the Wireless Button once, if the blue LED is changed to be solid, which means the pairing is successful. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1431655765 | Start the pair mode. |
Enable/ disable lock the configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Reset your Doorbell. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Reset the configuration parameters of your Doorbell. |
1431655765 | Reset to factory default settings. |
Get the Wireless Buttons battery status. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Normal battery level. |
255 | Low battery level. |
Set the default doorbell ringtone. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 100 | Specify the ringtone as default. |
Select a ringtone to play. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Stop playing |
1 - 100 | Play the specified ringtone. |
Control items. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | PLAY item. |
2 | STOP item. |
3 | PAUSE item. |
4 | NEXT item. |
5 | PREVIOUS item. |
Set the volume of ringtone for your Doorbell. Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 - 10 | Set the volume level of 0 to 10. |
To set which notification would be sent to the associated nodes in association group 1 when the state of Doorbell is changed Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send Nothing. |
1 | Send Hail CC. |
2 | Send Basic report CC. |
Enable/disable to send a notification to associated nodes in association group 1 when the Wireless Buttons battery is in low battery state. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable. |
Hardware Platform | ZM5101 |
Device Type | Siren |
Network Operation | Always On Slave |
Firmware Version | HW: 38 FW: 1.11 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-15110018 |
Z-Wave Product Id | 0x0086.0x0204.0x0038 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |