GE
Plug-in Smart Dimmer (Single Plug)
SKU: 28167 (ZW3104)
Quickstart
This is a
1. Follow the instructions for your Z-wave certified controller to include the device to the Z-wave network.2. Once the controller is ready to include your smart switch, single press and release the manual/program button on the smart dimmer to include it in the network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the GE Z-Wave Smart Lighting Control Plug-in Smart Dimmer. The lamp module enables wireless control of on/off and dim functions for standard incandescent table and floor lamps, as well as dimmable fluorescent, LED and CFL fixtures and more! Use the dimmer control to customize the lighting output and create the perfect ambiance for any room. The space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. The Dimmer provides one Z-Wave enabled outlet for the lamp you would like to control. Take control of your home lighting with GE Z-Wave Smart Lighting Controls!
| Reset to factory default | 1. If plugged in, unplug the Switch from the receptacle.2. Press and hold the top button for at least 3 seconds while you plug the switch into a receptacle.Note: This should only be used in the event your networks primary controller is missing or otherwise inoperable. |
| Inclusion | 1. Follow the instructions for your Z-wave certified controller to include the device to the Z-wave network.2. Once the controller is ready to include your smart switch, single press and release the manual/program button on the smart dimmer to include it in the network. |
| Exclusion | 1. Follow the instructions for your Z-wave certified controller to exclude a device from the Z-wave network.2. Once the controller is ready to Exclude your device, press and release the manual/program button on the smart switch to exclude it from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 10: Dim Rate Adjustments (When manually controlled)
PLEASE NOTE: Values should be entered using their signed values only, which means for example that a configuration value of 1 byte in size must have values in the range -128 to 127.Values specified here above or below the range specified by the value's size need to be converted to their 2's compliment value, or if your controller supports it, may be entered using hexadecimal notation. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of the steps |
Parameter 11: Dim Rate Adjustments (When receiving All-On/All-Off command)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Parameter 12: Dim Rate Adjustments (When receiving All-On/All-Off command)
Timing of the stepsPLEASE NOTE: Values should be entered using their signed values only, which means for example that a configuration value of 1 byte in size must have values in the range -128 to 127.Values specified here above or below the range specified by the value's size need to be converted to their 2's compliment value, or if your controller supports it, may be entered using hexadecimal notation. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of the steps |
Parameter 3: LED Light
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | LED Light on when Z-Wave turned OFF (Default) |
| 1 | LED Light on when Z-Wave turned On |
| 2 | LED Light always OFF |
Parameter 7: Dim Rate Adjustments (From Z-Wave Controller)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Parameter 8: Dim Rate Adjustments (From Z-Wave Controller)
Timing of the stepsPLEASE NOTE: Values should be entered using their signed values only, which means for example that a configuration value of 1 byte in size must have values in the range -128 to 127.Values specified here above or below the range specified by the value's size need to be converted to their 2's compliment value, or if your controller supports it, may be entered using hexadecimal notation. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of the steps |
Parameter 9: Dim Rate Adjustments (When manually Controlled)
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15080013 |
| Z-Wave Product Id | 0x0063.0x5044.0x3038 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |